Topic: #A108 by Amsterdam SOLVED: 1959 Corvette CERV I Corvette Engineering Research Vehicle

[Amsterdam]

Identify this car, for one point

[Amsterdam]

Ah!! front page attention!  Thank you.

[drum365]

Zora Arkus Duntov with the 1959 Corvette CERV1. (Corvette Engineering Research Vehicle)

[Amsterdam]

That frontpage feature paid off.
I am happy to award you youre very first point.

Welcome to Autopuzzles drum365!

[Amsterdam]

Some info

CERV 1 The idea of moving the engine behind the cockpit entered Arkus-Duntov's fertile imagination at Sebring in 1957 when the hastily prepared Corvette SS sports racer parboiled driver John Fitch's feet. Were it not for a failed suspension bushing after 23 laps of the 5.2-mile airport course, Fitch may not be walking today. Instead of lining the magnesium bodywork with insulation to block the engine and exhaust heat, Arkus-Duntov shrewdly concluded that the wiser solution would be to relocate the furnace...away from the driver.

Work began on a project car to study the feasibility of a mid-engine layout. Strictly speaking, the resulting Chevrolet Experimental Racing Vehicle (CERV) was not a Corvette. But the fact that this car pioneered the independent rear suspension that did make production for the 1963 model year establishes a clear lineage between the racer and the road car.

CERV was constructed with a steel-tubing space frame supporting two lateral fuel cells, a fuel-injected 4.6-liter (283 cubic inch) mostly aluminum V-8, and a four-speed transaxle. Sandwiching the gearbox between the engine and a Halibrand differential moved the driver's seat well forward in the 96-inch-long wheelbase. Sixty percent of the car's 1450-pound dry weight rested on the rear wheels. With 353 horsepower on tap, CERV's performance was exemplary.

Arkus-Duntov aspired to campaign CERV at Indianapolis if and when GM dropped its ban on direct racing involvement. In the fall of 1960, the car demonstrated competitive speed climbing Pikes Peak. Following limited race track tuning, it made a few demonstration laps before the US Grand Prix at Riverside, California. That prompted a name change - from Racing to Research - as a nod to GM's no-racing edict. To close out the CERV 1 era in a memorable way, Arkus-Duntov installed a 6.2-liter small-block V-8 and toured the five-mile circular track in Milford, Michigan, at 206 mph.

[Otto Puzzell]

That frontpage feature paid off.
I am happy to award you youre very first point.

Welcome to Autopuzzles drum365!

Welcome, drum365 - keep up the good work, and maybe you'll come to be known as the drum that can't be beat!

[drum365]

Thanks for the welcome, Amsterdam and Otto!

I have been checking this site regularly for a long time, but haven't been able to identify anything until this puzzle popped up. (And it wasn't the car - I looked at the pic and thought, wait a minute, isn't that Duntov? The rest was easy!)

Thanks again. Glad I finally got a point! Yay!

[grobmotorix]

Here´s a 1961 Riverside racing pic:

[Otto Puzzell]

Period pics

[Ecnelis]

It is going up for auction next month!

From rmauctions.com:

N/A bhp, 377 cu. in. OHV aluminum experimental V-8 engine, four-speed manual transmission with lightweight clutch, independent front and rear suspension with variable-rate coil springs, shock absorbers, and front stabilizer bar, and four-wheel heavy-duty iron-lined cast aluminum finned drum brakes. Wheelbase: 96 in.

The most important GM Engineering vehicle ever offered at auction
Zora Arkus-Duntov’s personal Corvette engineering test bed
Used to develop the 1963 Sting Ray’s independent suspension, among other features
Formerly of the Briggs Cunningham and Miles Collier collections
Restored in its final 1964 cosmetic and mechanical form
Innumerable awards and featured in numerous publications
The car from which the modern Corvette was born


The Chevrolet Engineering Research Vehicle (CERV) was not originally created as a Corvette test bed, nor was it created to do entirely what its name claimed. Ostensibly, it would be a functional single-seat racing vehicle on which Chevrolet engineers could experiment, developing new tricks for the entire range of Bow Tie cars. However, projects in which GM’s Director of High Performance Vehicles, Zora Arkus-Duntov, was involved generally had an ulterior motive. In this case, it was that CERV could actually win races.

Arkus-Duntov started dreaming mid-engined at Sebring in 1957, when, driving one of the specially built Corvette SS cars, he struggled with heating problems. Initially, he looked at a Corvette with a rear transaxle, built as a prototype that year and dubbed the Q Corvette, but when Chevrolet unofficially began to loosen their ban on racing-related activities while also preparing to introduce the rear-engined Corvair, he was able to turn in a different direction. He proposed that a racing car with a Corvair-style drivetrain configuration could offset public skepticism about a rear-engined car.

Creating the racer was the task of Arkus-Duntov and his engineers, Harold Krieger and Walt Zetya. Initially known as the “R Car,” its specifications were purposely drawn as broadly as possible; its dimensions would make it eligible for the Indianapolis 500, but it would also fulfill its creator’s primary criteria of a vehicle suitable for climbing Pikes Peak. The “build” began in early 1960 but was not completed until late summer, due to Arkus-Duntov’s involvement with Briggs Cunningham’s Corvette Le Mans team.

At the time of its completion, the vehicle, now officially known as CERV but also as Hillclimber for its intended purpose, was a thoroughly exotic car. Its basic skeleton was a chromium-molybdenum steel tubular space frame, resembling the Italian superleggera bodies created by Touring, triangulated both front-to-rear and laterally and weighing a mere 125 pounds. The body, designed by Larry Shinoda and Tony Lapine, was molded in two layers of fiberglass and weighed only 80 pounds.

Originally powering this ultralight shell was a fuel-injected, all-aluminum, 289-cubic inch V-8, based upon an earlier Corvette prototype engine with a silicon alloy block (enabling the use of production Corvette pistons directly in the cylinder bores, without the use of cylinder liners) and mostly aluminum engine accessories, including the flywheel, pressure plate, and water pump housing. Other components were even lighter, with magnesium used for the clutch housing and ultralight intake setup. Being rear-mounted, the intake could be as tall as Zora wanted and sprouted 16-inch-tall stacks and a finned plenum atop that gulped cool air from inlets at the back of the pod behind the headrest. Based upon an earlier Arkus-Duntov design for a 315-brake horsepower 289 V-8, it proved to make 112 percent of that horsepower at 6,200 rpm.

Due to packing requirements, the drivetrain was at least somewhat conventional, with a hydraulic clutch and reverse-geared four-speed transmission hung off the back. Corvette SS-derived quick-change gearing provided 13 optional ratios, from 2.63:1 to 4.80:1. The rear halfshafts were stressed members, with the SS’s Halibrand inboard Corvette 11-inch brakes. An entire Corvette SS front suspension assembly was used, including a steering rack with a quick-ratio Saginaw box.

The finished CERV, weighing 1,450 pounds dry, showed up at Pikes Peak in September of 1960 and began what would be an extremely varied life.

“A BUNDLE OF DYNAMITE”

Over the course of 60 or so runs up and down a 0.9-mile-long segment of Pikes Peak, CERV proved not well-suited to hillclimbs. No problem, Arkus-Duntov decided; that was why they had made the car capable for Grand Prix as well. The car was track-tested with Firestone, after which Arkus-Duntov scheduled time for the car at Riverside Raceway, just prior to the Grand Prix there, as well as permission to debut it before the race. At Riverside, Arkus-Duntov, Dan Gurney, and Stirling Moss all drove CERV publically; Gurney and Moss both lapped the course in a competitive 2.04 seconds.

Back at the GM Proving Grounds, Arkus-Duntov slid behind the wheel, broke 170 mph, and started to ponder Bill France Sr.’s famous $10,000 reward for the first car that could lap Daytona at 180 mph. He brought the car there, reached 162 mph, and decided that more horsepower was the answer, despite somewhat squirrely handling—an atypically unnerved Jerry Titus referred to it as “a bundle of dynamite.”

The team experimented and developed a 17-psi TRW turbocharged port-injection set-up with reversed stacks. Running at 8.5:1 compression, CERV made 500 horsepower at 6,000 rpm on a dynamometer, making it, reportedly, the most powerful engine tested by General Motors until the Mk IV “Mystery Motor.” It was so powerful, in fact, that when it ran, it lifted the front wheels, leading to a Shinoda restyling of the car’s front end with aerodynamic modifications, giving the car a profile resembling an F1 or Indianapolis car.

By 1964, CERV II was already underway, and the car offered here, the original CERV, thus became known retrospectively as CERV I. That year, it received its seventh engine, a Hilborn fuel-injected 377-cubic inch V-8, specially cast by Alcoa at a reported cost of $284,000 and producing unknown (but, it can be assumed, very great) horsepower. With this engine, at one of its last outings that year, Arkus-Duntov took the highly revised CERV I to 206 mph on the banked track of the GM Milford Proving Grounds. It was another 22 years before Bobby Rahal would go faster at the 1986 Indianapolis 500.

THE ONE THAT GOT AWAY

Like most General Motors test vehicles, the most that CERV I could look forward to, now that a replacement was underway, was the yawning maw of an industrial shredder. Arkus-Duntov stepped forward, however, with his typical desire to protect his creations, and instead had the car restored, keeping it in its final 1964 Shinoda configuration with the aluminum 377 V-8.

In 1972, the car, along with CERV II, was gifted by GM upon Briggs Cunningham for his automobile museum in Costa Mesa, California, with the idea that it would be a safe place for a prototype: as a museum, the car would stay there for many years to come (and never escape into “private” hands). Like most collections, however, Cunningham’s was not permanent, and when he sold the majority of his collection to Miles Collier at the end of 1986, both CERVs went along with the deal.

The current owner acquired the car from Mr. Collier and has lovingly preserved it ever since in his own private museum, alongside numerous other world-class and important Corvettes. It has earned innumerable awards, far too many to record here, including a recent induction to the Bloomington Gold Great Hall.

One must consider the importance of this car. It was a pioneer in the use of aluminum, and its transverse leaf-spring independent rear suspension is the predecessor of the same basic design that Corvette is still using today, 55 years after this car was built. For four years, it ran at Riverside and on the test track at Milford, tested numerous engines being developed for possible use in the Corvette, pioneered new methods and features that would influence America’s Sport Car for decades, and was, to sum it all up, Zora Arkus-Duntov’s personal pet project, test bed, and dream factory.

It stands aside such experimental landmarks of GM history as the Buick Y-Job, the LeSabre, and the turbine-powered Firebirds, with one major exception: it is for sale.

Bidders interested in the 1960 Chevrolet CERV I are strongly encouraged to review the car’s fascinating, extensive multi-volume history file. The files are available for viewing at the Access the Knowledge desk.

[grobmotorix]